近年來，斷橋鋁門窗在現在很多家庭中應用的是比較多的，隨著現在人們對生活質量要求變高，斷橋鋁門窗在安裝時就需要有專業的安裝團隊，但是在檢查安裝質量是否有保證時，在那些地方能看出來呢？
In recent years, broken bridge aluminium doors and windows are widely used in many families. With people's higher requirements for the quality of life, broken bridge aluminium doors and windows need professional installation team when they are installed. But when checking whether the installation quality is guaranteed, where can we see it?
想要看斷橋鋁門窗安裝的是否專業，在進行安裝時要按照：清理洞口-窗框調整-窗框固定-玻璃安裝-窗扇安裝-縫隙封修的順序進行，下面來詳細了解下：
To see whether the installation of broken bridge aluminum doors and windows is professional, the installation should be carried out in accordance with the sequence of clearing holes - window frame adjustment - window frame fixing - glass installation - window fan installation - gap sealing. The following is a detailed understanding:
1、窗框調整
1. Window Frame Adjustment
將墊塊置放在下層墻上，注意測量標記；將窗框置放在窗洞內，向二側移動校準在窗洞內的位置；校準下框的水平度，下框塞墊，同時調整與墻體連接處，及墻面平均縫隙距離；注意上框的縫隙，在豎框上端，用銷釘固定框架和調整豎框與邊緣的接觸，使用水平儀，窗框的型材應平直在使用銷釘時不要使型材變形。
Place the pads on the lower wall, pay attention to the measurement marks; place the window frames in the window holes, move to both sides to calibrate the position in the window holes; calibrate the level of the lower frame, the lower frame pads, and adjust the distance between the wall and the average gap of the wall; pay attention to the gap of the upper frame, fix the frame with pins at the upper end of the vertical frame. And adjust the contact between the vertical frame and the edge, using the level meter, the profile of the window frame should be straight when using the pin, do not make the profile deformed.
在那幾點地方能看出斷橋鋁門窗安裝的是否專業
Where can I see whether the installation of broken bridge aluminium doors and windows is professional?
2、清理洞口
2. Cleaning the hole
保證洞口沒有影響安裝的雜物，保證施工的正常運行。
Ensure that the opening does not affect the installation of debris, ensure the normal operation of the construction.
3、窗框固定
3. Window frame fixing
斷橋鋁門窗采用固定片固定方式，可吸收墻體的變形，固定片為一鍍鋅鋼板制件，一端通過螺釘與鋼副框連接，使其在連接框架與墻體時無任何張力，用射釘槍將固定片固定在墻體上，這一固定片對框架產生的橫向和豎向變動力，通過型材固定部位的極微小的轉動和伸縮維持平衡。
Aluminum doors and windows of broken bridges are fixed by fixing sheets, which can absorb the deformation of the wall. The fixing sheet is made of galvanized steel sheet. One end of the fixing sheet is connected with the steel sub-frame by screw, so that there is no tension between the frame and the wall. The fixing sheet is fixed on the wall by shooting nail gun. The transverse and vertical changes of the fixing sheet on the frame are caused by the fixing sheet. Force is maintained by the slight rotation and expansion of the fixed part of the profile.
4、玻璃安裝好后，安裝開啟扇
4. Install the opening fan after the glass is installed.
平開窗是將開啟扇通過合頁與固定在洞口的窗框連接；小的誤差可做適當調整，情況嚴重的要卸下玻璃進行調整，檢查斷橋鋁合金窗扇與窗框的吻合是否均勻，如不均勻在窗框的鎖定側進行校準。
Flat window opening is to connect the opening fan with the window frame fixed at the opening through the hinge. Small errors can be adjusted properly. In serious cases, the glass should be removed to adjust. Check whether the match between the broken bridge aluminum alloy window fan and the window frame is uniform, such as non-uniform calibration on the locking side of the window frame.
5、斷橋鋁門窗玻璃及窗扇安裝
5. Installation of Broken Bridge Aluminum Door and Window Glass and Window Fan
框架在洞口中安裝好后，進行玻璃及開啟扇的安裝，玻璃在加工廠已預制完成，每塊玻璃都有標號圖，按分格圖上相應的標號位置將玻璃通過軟性接觸放在指定的位置框墊塊上，調整玻璃的左右位置，使玻璃的左右中心線與分格的中心線保持一致，用扣條將玻璃固定在框架上。
After the frame is installed in the hole, the glass and the opening fan are installed. The glass has been prefabricated in the processing plant. Each piece of glass has a labeling map. According to the corresponding labeling position on the grid diagram, the glass is placed on the designated position frame cushion block through soft contact. The left and right positions of the glass are adjusted so that the left and right centerlines of the glass are separated. The center line of the lattice is consistent and the glass is fastened to the frame with a buckle.http://dctv01.com/
